Gigo's Bulletin Board

Back number

[Return to home]

SHSMOD1.9

shsmod V1.9 release (9/18/2000) http://www.devdrv.com/
copyright(c) 1996-2000 O.Imaizumi, Device Drivers Limited.

NS PC87309 at 002eh detected
NS Patch driver detected
COM1 (03f8h): Supported, Mode = High
COM2 (02e8h): Supported, Mode = High
Notify -- PS/2 Mouse detected(03, c427)

NOT SURE IF ITS ANY FASTER
Any suggestions on telling if its speeding up my port speed?

I have this problem also,, was in another post

shsmod V1.7a (29-Aug-1998)
SMC37b80x at 03f0h detected
SMC/AMI Patch driver detected
Port1(03f8h) Serial Speed Mode: High
Port2 disabled
comment:
When I load the patch everything appears ok.

When I restart my win98 and invoke my modem, it can not be found. When I
uninstall shsmod it works fine.

Note , have noticed that with all settings at 230400 it wont work,, but if I go in after all of the setup and patches and change the modem properties back to 115200 in the dialup properties only then it will connect,, otherwise it says hardware error couldnt connect to modem.

Any assistance would be greatly appreciated. Thank you. weslucky@hotmail.com

com4

I have a internal modem, I can use SHS?
Tank

com4

I have a internal modem, I can use SHS?
Tank

com4

I have a internal modem, I can use SHS?
Tank

com4

I have a internal modem, I can use SHS?
Tank

Mkbootcd and 2.88 floppy image

I have successfully gotten all of the 1.44 Mb images to boot. I took an image from a 2.88 floppy drive. My settings for those images were:
-T3
-C1
bigimage.ima

During the boot process the initial boot info will flash on the screen..
"Starting MS DOS"
then hang.
are these the correct settings?

shsmod ver 1.7c - modem not recognized

hello, i just dl shsmod ver 1.7c for my Winbond W83977EF chip.
installation worked fine, com1 (mouse) is low, com2 (modem) is high.
problem: computer does not recognize the modem any more (it says there
are no modems installed)
i have an isdn line with Eicon DIVA T-A modem, and i run windows 98
first edition
i noticed that in the Properties tab of my internet connection there are
TWO modems listed:
Eicon DIVA T_A ISDN Modem (which is not recognized, saying that is not
installed)
Eicon DIVA T_A ISDN Modem Pnp (which is recognized as installed)

i went to the registry at
"HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Class\Modem\" and
i had two listings of modems. I deleted the one with Eicon DIVA T_A
ISDN Modem (labelled "0000") and left the other one (labelled "0001").
After reboot, in the Properties of my internet connection are still
listed two modems. internet connection works fine.
any ideas highly appreciated
natha@image.dk
thank you.
dr

shsmod ver 1.7c - modem not recognized

hello, i just dl shsmod ver 1.7c for my Winbond W83977EF chip.
installation worked fine, com1 (mouse) is low, com2 (modem) is high.
problem: computer does not recognize the modem any more (it says there
are no modems installed)
i have an isdn line with Eicon DIVA T-A modem, and i run windows 98
first edition
i noticed that in the Properties tab of my internet connection there are
TWO modems listed:
Eicon DIVA T_A ISDN Modem (which is not recognized, saying that is not
installed)
Eicon DIVA T_A ISDN Modem Pnp (which is recognized as installed)

i went to the registry at
"HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Class\Modem\" and
i had two listings of modems. I deleted the one with Eicon DIVA T_A
ISDN Modem (labelled "0000") and left the other one (labelled "0001").
After reboot, in the Properties of my internet connection are still
listed two modems. internet connection works fine.
any ideas highly appreciated
natha@image.dk
thank you.
dr

shs17.zip(SHSMOD V1.7) Aug/29/1998 For Win95/98

My sys: IBM Aptiva 2142S62. Pentium II with MMX. Purchased in Dec 1997
Win95B, OSR2.1
Modem: Lucent WinModem 56KFlex; current drivers are V-90,
Located on COM1
-----------------------
I installed SHSMOD on my system May/23/2000
I followed Instructs per the Readme for SHS17.ZIP 25-Aug-98 file.
Info shown on my MS-DOS window was the same as indicated in this file.
-- But info in my win95 Regedit was different than what you gave in the

Apendix "How To Change Modem Data Rate in Windows 95"
You said, Search COMx with regrdit,
It's found in
HKEY_LOCAL_MACHINES_\System\CurrentControlSet\Services\Class\Modem\nnnn\attachto
and under bps 57,600 through 921,600 etc.
-----------
I did a seach for COM1 (port for my modem)and did not come up with that info/
Here is what my search showed:
HKEY_LOCAL_MACHINES\Enum\ISAPNP\GCV5719\0005418A

REGEDIT4

[HKEY_LOCAL_MACHINE\Enum\ISAPNP\GVC5719\0005418A]
"HardwareID"="*GVC5719,*HSM0140,ISAPNP\\GVC5719"
"HWRevision"="1.0.01"
"DeviceDesc"="Lucent Win Modem"
"Class"="Modem"
"Driver"="Modem\\0000"
"Mfg"="Lucent"
"ConfigFlags"=hex:00,00,00,00
"PORTNAME"="COM1"
"ModemEEPROM"=hex:19,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,55,01,05,0e,00,32,00,0e,00,32,00,01,00,00,00,91,00,dd,03,0e,\
00,06,00,00,00,00,00,23,00,00,00,12,00,00,00,00,00,00,00,00,10,00,00,00,03,\
04,00,04,00,00,00,00,00,51,07,00,00,65,17,94,2a,0d,27,b6,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,c1,65,13,10,47,8d,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00
"FriendlyName"="Lucent Win Modem"
"Settings"=hex:02,10,00,c0

[HKEY_LOCAL_MACHINE\Enum\ISAPNP\GVC5719\0005418A\LogConfig]
"0000"=hex:00,04,00,00,00,30,00,00,20,00,00,00,02,00,00,00,01,00,0c,00,f8,03,\
ff,03,00,00,00,00,f8,ff,08,00,f8,03,ff,03,00,00,00,00,10,00,00,00,04,00,00,\
00,00,00,04,00,10,00,00,00,0c,00,00,00,03,00,00,00,00,07,e0,00,0c,00,00,00,\
03,00,00,00,00,06,e0,00,20,00,00,00,02,00,00,00,01,00,0c,00,08,01,0f,01,00,\
00,00,00,f8,ff,08,00,00,01,ff,03,00,00,00,00,00,00,00,00
"0001"=hex:00,04,00,00,00,30,00,00,20,00,00,00,02,00,00,00,01,00,0c,00,00,00,\
00,00,00,00,00,00,f8,ff,08,00,f8,03,ff,03,00,00,00,00,10,00,00,00,04,00,00,\
00,00,00,00,00,00,04,00,00,0c,00,00,00,03,00,00,00,00,00,e0,00,0c,00,00,00,\
03,00,00,00,00,00,e0,00,20,00,00,00,02,00,00,00,01,00,0c,00,00,00,00,00,00,\
00,00,00,f8,ff,08,00,00,01,ff,03,00,00,00,00,00,00,00,00
"0002"=hex:00,04,00,00,00,30,00,00,20,00,00,00,02,00,00,00,01,00,0c,00,00,00,\
00,00,00,00,00,00,f8,ff,08,00,f8,03,ff,03,00,00,00,00,10,00,00,00,04,00,00,\
00,00,00,00,00,b8,9e,00,00,0c,00,00,00,03,00,00,00,00,00,e0,00,0c,00,00,00,\
03,00,00,00,00,00,e0,00,20,00,00,00,02,00,00,00,01,00,0c,00,00,00,00,00,00,\
00,00,00,f8,ff,08,00,00,01,ff,03,00,00,00,00,00,00,00,00
"0003"=hex:00,04,00,00,00,30,00,00,20,00,00,00,02,00,00,00,01,00,0c,00,00,00,\
00,00,00,00,00,00,f8,ff,08,00,e8,03,ef,03,00,00,00,00,10,00,00,00,04,00,00,\
00,00,00,00,00,b8,9e,00,00,0c,00,00,00,03,00,00,00,00,00,e0,00,0c,00,00,00,\
03,00,00,00,00,00,e0,00,20,00,00,00,02,00,00,00,01,00,0c,00,00,00,00,00,00,\
00,00,00,f8,ff,08,00,00,01,ff,03,00,00,00,00,00,00,00,00
"0004"=hex:00,04,00,00,00,30,00,00,20,00,00,00,02,00,00,00,01,00,0c,00,00,00,\
00,00,00,00,00,00,f8,ff,08,00,e8,02,ef,02,00,00,00,00,10,00,00,00,04,00,00,\
00,00,00,00,00,b8,9e,00,00,0c,00,00,00,03,00,00,00,00,00,e0,00,0c,00,00,00,\
03,00,00,00,00,00,e0,00,20,00,00,00,02,00,00,00,01,00,0c,00,00,00,00,00,00,\
00,00,00,f8,ff,08,00,00,01,ff,03,00,00,00,00,00,00,00,00
"0005"=hex:00,04,00,00,00,30,00,00,20,00,00,00,02,00,00,00,01,00,0c,00,00,00,\
00,00,00,00,00,00,f8,ff,08,00,f8,02,ff,02,00,00,00,00,10,00,00,00,04,00,00,\
00,00,00,00,00,b8,9e,00,00,0c,00,00,00,03,00,00,00,00,00,e0,00,0c,00,00,00,\
03,00,00,00,00,00,e0,00,20,00,00,00,02,00,00,00,01,00,0c,00,00,00,00,00,00,\
00,00,00,f8,ff,08,00,00,01,ff,03,00,00,00,00,00,00,00,00

===========================================================================
My com2 port setting (from Sys Properties/Device Mngr)Shows in the Bits/second
box:230400, 46800,921600.

I cannot find this info for COM1. As you know in Win95, Only the Unassigned
com ports shows, the COM port in use does NOT show in the Sys Properties Device
Manger tab windows.

So, How Do I Get This Changed In Win95?

Curtis

The SHSMOD was no longer supported in this bulletin board.

Please write to Mr.tom's one. :-)

http://www.devdrv.com/bbs/eshsmod.cgi

re;Support for ASUS P55T2P4 ??

The winbond 83877F,83877AF don't have high-speed mode.
You find no suitable divisor value for UART x16 clock, If you check data sheet
carefuly.

The 83877TF,83877ATF are able to set suitable divisor value.

Serial High Speed mode utility Ver.1.7

I have a FIC VA 503+ mainboard and I used this utility and it does increase my uart speed but I am getting A slower connection speed when its enabled
according to my modem diagnostic my max connection speed is now 33.6 as aposed to the 115200 I get when its not enabled. another issue is that windows continues to say its still using a 16550 uart in its modem diagnostics utility. this should say 17550 should it not? after all that is the max speed of my bios chip acording to winbound.
also when I attempt to set my bits per sec rate to 230400 my modem will not connect at all.
I have a diamond supra express external modem & I don't understand this its onboard uart is capable of a 230k DTE rate acording to diamond.
please HELP I don't get it!

Support for ASUS P55T2P4 ??

Please add support for the common P55T2P4 (Socket 7), which runs in many deskops with a 400 MHz AMD. It has (in my 2 boards) a Winbond 83877 F chip onboard.
Thanks a lot
Ulli

A happy new year !

test

test writing

ASUS MEW w. i810 and PPGA cel.

Sucks. The utility cannot identify the serial chip on my motherboard.
comment:
I need bunddling BAAAAD, please help me! I'll try anything.
MB: ASUS MEW DC-100, i810
modem: Eicon DIVA ISDN

Celeron 450 MHz

-
comment:
Are SHSMOD ever gonna support win2000??? And when??

Does anyone have any other tips how to speed the serialport up i win2000???

Best regards Allan

ABIT BX6 Rev 2.0

shsmod V1.8beta03 (07-Sep-1999)
Winbond W83977EF at 03f0h detected
Old patch driver detected
COM0(03f8h):Supported, Mode = Low
COM1(02f8h):Supported, Mode = High
Warning -- This system has unsupported UART chip.
The patch may cause problem.

comment:
This beta version is giving an error, while shs17d does not give an error.

Also, shsmod should have a way of patching the serial.vxd even when a compatible chipset is not detected. Then people with compatible internal modems but incompatible com port chipsets could also take advantage of over 115k.

Anyone having trouble making regedits for over 115k and people needing a patched serial.vxd file, since they can't patch it with shsmod, check my web site for more info at http://www.downloadit.gr/~v_laessig

re;amd k6 200 motherboard: Iwill P55XB2

>Can the ali m5133 run faster than 115200?

I have never confirmed it.
But, there is a report in BBS(Japanese).

I don't do the support of shsmod in this bulletin board any more.
Please write to Mr.tom's one. :-)

amd k6 200 motherboard: Iwill P55XB2

shsmod V1.7c (17-feb-1999)
ali m5133 at 03f0h detected
sms/ali patch driver detected
Port 1 (03f8h) Serial Speed Mode: High
Port 2 (02f8h) Serial Speed Mode: High
comment:
Hi
Before I install shsmod i got speed mode = low,
after the install i got speed mode = high.
Before and after the install i could set the max. speed to the modem to 460800.
But before and after the install I got the same speed when I chek the the modem
115200.
My isdn modem i a zyxel omni net plus, the serial port on the modem can run at
460800.
I use windows 95 OS2.
Can the ali m5133 run faster than 115200?

Windows98

shsmod V1.7a (29-Aug-1998)
*Check B72x: port=03f0, ini1=55, ini2=55, idx=20 -> id=ff, rev=ff
*Check B72x: port=0370, ini1=55, ini2=55, idx=20 -> id=42, rev=01
*Check B77x: port=03f0, ini1=55, ini2=55, idx=20 -> id=ff, rev=ff
*Check B77x: port=0370, ini1=55, ini2=55, idx=20 -> id=42, rev=01
*Check B78x: port=03f0, ini1=55, ini2=55, idx=20 -> id=ff, rev=ff
*Check B78x: port=0370, ini1=55, ini2=55, idx=20 -> id=42, rev=01
*Check B80x: port=03f0, ini1=55, ini2=55, idx=20 -> id=ff, rev=ff
*Check B80x: port=0370, ini1=55, ini2=55, idx=20 -> id=42, rev=01
SMC37B80x at 0370h detected
+0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F
00:00 00 00 03 00 00 00 05 00 00 00 00 00 00 00 00
10:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20:42 01 39 00 04 00 70 03 00 00 00 00 00 00 00 00

comment:
Hi Gigo,

In your helpfile you wrote:
Appendix.
How to change modem maximum data rate in windows95.

1. Search "COMx" with regedit.
It will find at
HKEY_LOCAL_MACHINES\System\CurrentControlSet\Services\Class\Modem\nnnn\
attachedto
ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®
Sorry... but i can`t find this entry in my regedit :-(

2. edit properties 24th(0x18th) to 27th byte.
ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®°
I can`t find this entry in my regedit :-(

bps value
57,600 00 E1 00 00
115,200 00 C2 01 00
230,400 00 84 03 00
460,800 00 08 07 00
921,600 00 10 0E 00
ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®ˆ®
I can`t find this entrys in my regedit :-(
So i can`t change nothing.

I am using windows98 (germany).
My modem supports 230,4 bps
Computersystem: Pentium II/ 400 Motherboard: Intel SR 440BX

Please help me to change/take effect this high speed for my win98
system.

Thank you very much
Andreas

New Over115K Support Page

John,

I am developing the new Over115k Support page below.

http://www.devdrv.com/shsmod/

The latest version is V1.7d, and V1.8b3 is available.
Please link to my page.

Thanks,

na

na
comment:
I posted a copy of shsmod V1.7c on my web page for download, since this site gives an error on that link. I also have written a small utility called Powerup Com for win95/98 to tweak the registry to allow over 115k max port speeds. See my web site for additional instructions and some screenshots of my registry settings if you are having trouble getting over 115k to work.

abit bh6

shsmod V1.7a (29-Aug-1998)
Winbond W83977 at 03f0h detected
Winbond Patch driver detected
Port1(03f8h) Serial Speed Mode: High
Port2(02f8h) Serial Speed Mode: High

comment:
works great .. thanks

ABIT BX6R2

Not yet up and running
comment:
Would you please advise where I may download serial.vxd.
I cannot get it from www.downloadit.gr/~v_laessig/download/
I am looking forward to trying shsmod.
Thanks heaps.

intel pr440fx

shsmod V1.7a (29-Aug-1998)
NS PC87308 at 002eh detected
NS Patch driver detected
Port1(03f8h) Serial Speed Mode: High
Port2(02f8h) Serial Speed Mode: High
comment:

Tried to d/l version 1.17c, but received a "404 not found on this server"
error. Just thought you'e like to know.

Soyo 6be+

shsmod V1.7c
Not detected......
comment:
HI...
I have a question...
i use soyo 6be+ m/b
it is not detected....
6be+ m/b has ite chipset....
how can i set it up??
help me...

driftwood

Japanese residents interested in beautiful driftwood from Canada please email and let me know.I travel all over the coast and see lots of it.

FIC PA2013

I installed SHSMOD software with install, when I unzip file. But it doesn't work. Max speed 115200 as before.
comment:
I don't where to find serial.vxd update.
Modem name is USRobotics Message Plus

Thanks for help and a prompt reply.
Best regards

FIC PA2013

I installed SHSMOD software with install, when I unzip file. But it doesn't work. Max speed 115200 as before.
comment:
I don't where to find serial.vxd update.
Modem name is USRobotics Message Plus

Thanks for help.
Best regards

Notebook

shsmod 1.7c
NS PC87338
comment:
Hi!

I am using shsmod on my Notebook and I have a problem.
Sometimes while sending data the sending stops and no data could be send anymore.
The Error is that there is a timeout because of the Output-Buffer not getting empty.
But looking at the output-buffer-counter, it says there are no bytes to send left.
This happens only at speeds higher than 115200.

It is impossible to send more data until reconfiguration of the serial port.

Second thing:
Why haven't you enabled the 32-Byte FIFO on the NS PC87338?
Just change
and al,0CFh
or al,010h
to
and al,0C0h
or al,015h

Greetings....

Abit BX6 -rev2

>C:\Program Files\shsmod>shsmod install.pif

To install SHSMOD,
double click install.pif directly or
SHSMOD patch

To uninstall
shsmod depatch

The manual is included in shs17.zip.
Most newer version such as shs17d.zip..SHS18B02.zip hasn't manual yet.

Abit BX6 -rev2

C:\Program Files\shsmod>shsmod
shsmod V1.7c (17-Feb-1999)
Winbond W83977EF at 03f0h detected
Original driver detected
Port1(03f8h) Serial Speed Mode: Low
Port2(02f8h) Serial Speed Mode: Low


comment:
Eicon diva ISDN T/A

When I try to install SHSMOD I get the following:

C:\Program Files\shsmod>shsmod install.pif
shsmod V1.7c (17-Feb-1999)
usage:shsmod [port# [h/l/d]]
shsmod port# baud (NS chip only. except PC87308)
shsmod patch|depatch [sysdir]

Comments will be appreciated

thks
Vagn

EPoX

I got an EPox EP-58MVP3C-M (AT-board, socket 7) and a EICON-DIVA TA running Win-98.
It goes allright with 230400 bps - just correct the autoexec.bat from

SHSMOD B H
to
SHSMOD 2 H (if your mouse use COM-1)

Hey Steen

SSHMOD

Hi,

Just installed your utility and hum! don't know what to do with it.
Your reports on this utility is not much so I can't really tell if it's
faster or not.

shs17 on Abit BH6

No problem in installation on my Abit BH6. Able to boost speed up to 115200bps.

But I can only get maximum of 115200bps, even though all my settings (e.g com2 port and even win.ini setting are set to 921600bps.
I was wondering, since my Mboard can support up to 921600bps, is it possible to boost it up to that speed?
Am using Aztech 56K modem over normal telephone line.

And thanks for the great software.

P2-266 oc'd to 300, MB: Asus P2L97 (LX)

SHSMOD 95/98: perfect - works great!
... but I'm primary using WinNT :(
SHSMOD NT: Thumbs down. Doesn't work with WinBound chips. Crappy.
comment:
Hi.

When will there be a new WinNT4 version that supports WinBound chips??? Nearly all new motherboards have WinBound chips, so I would really like a new version of SHSMOD!

I am REALLY looking forward to a SHSMOD that supports WinBound chips!!!

HP Pavilion 8250


Here is my report on the installation of

AFTER INSTALLATION of SHSMOD:
shsmod check:

shsmod V1.7a (29-Aug-1998)
NS PC87309 at 015ch detected
NS Patch driver detected
Port1(03f8h) Serial Speed Mode: High
Port2(02f8h) Serial Speed Mode: High

comment:

Here is my report on the installation of

Report & Related news BBS,
http://www1.yk.rim.or.jp/~gigo/bbs/shscatbbs.cgi (OLD URL ???)
Please feel free to write.

MY SYSTEM:

HP Pavilion 8250

Serial chip MS PC87309

Microsoft Windows 98 4.10.1998
Upgrade using OEM CD /SrcDir=E:\WIN98 /IQ /U:xxxxxxxxxxxxxxxxx
IE 5 5.00.2314.1003
Uptime: 0:01:23:23
Normal mode
On "PAVILION" as "(UserName)"
Hewlett-Packard
GenuineIntel Pentium(r) II Processor Intel MMX(TM) Technology
128MB RAM
74% system resources free
Windows-managed swap file on drive C (1867MB free)
Available space on drive C: 1867MB of 5732MB (FAT32)

re: How to change modem maximum data rate in windows95.

I was unable to use your method of using REGEDIT to edit the properties of the BPS and Value.
Using the Control Panel, I was able to set COM1 to 921,600. Formerly it was set at 115,200. COM2 does not show in the Control Panel. I use COM2 for my internal modem.

My modem only allows 115,200.

Thank you for the use of your program.

re;SHSMOD

check
http://www.downloadit.gr/~v_laessig/

ABIT BX6-rev2

We (Mr.Takeuchi & Tsuruzo & me) discussed about this issue on Japanese version
of my BBS nearly half year ago.

The result is: The some type of RS232C buffer can't drive in higher speed.
I could not recommend chip for over115K because too few report.
Unfortunately, we can't determine what kind of buffer is on board by software.

Mr.takeuchi exchange his RS232C buffer to Hi-speed one. He got good result.
And he found another way too.
"if you don't worry about EMC, remove noise filter or ferrite bead is good
solution."

Mr.Tsuruzo wrote:
"shorten cable"

ABIT BX6-rev2

shsmod V1.7C
W83977EF - Chip
comment:
Hi!

The patch works with no problems, but I am not able to use rates higher than 115200 without errors.

Looking on the serial port with an oscilloscope, I can see that the signal quality is very very bad.
230400 works with errors (many), everything over 230400 - forget it.
Is this normal with this MB?

On my notebook (NS PC87338 chip) everything works up to 921600 without any problems...

Greetings....

SHSMOD

I can follow all the instructions up to and including finding the registry value but once there there seem to be no reference to bytes 24-27 as per instructions. The values I get are: 0000, 0008, 0010, 0018, 0020, 0028, 0030, 0038 and 0040 although I can see the value C2 01 00. Please help!

SHSMOD

I can follow all the instructions up to and including finding the registry value but once there there seem to be no reference to bytes 24-27 as per instructions. The values I get are: 0000, 0008, 0010, 0018, 0020, 0028, 0030, 0038 and 0040 although I can see the value C2 01 00. Please help!

re;mkbootcd

These files are copyrited.
You must build it from your own files.

There is a good article about this work.
please see
http://www.heise.de/ct/english/99/11/206/

mkbootcd

Hi
I am working through your process to make a bootable cd but I cannot find
the files msdos.bmi, win95.bmi, win95rpr.img or floppy14.img. What are these
files and where are they located? Do they now have a different name?
Thanks as I working at making a bootable rescue cd.
david

Dell Latitude - Portable computer

shsmod V1.7a (29-Aug-1998)
SMC37N958FR at 03f0h detected
SMC/ALI Patch driver detected
Port 1 (02f8h) Serial Speed Mode: High
Port 2 Disabled
comment:
Is this program only designed to work on external modems? Is it possible to speed up internal or pcmcia modems?

re;Alpha NT version of SHSMOD

There is a NT4.0 editions for SMC chip on x86 architecture.
It doesn't support other chip maker and another architecture.

It was made from old source code that was included in DDK sample.
If you have DDK and compiler for alfa the porting is not so difficult
because the part of C source code that was added by me is archived.
I think.

please see
http://www.os.rim.or.jp/~gigo/over115K/index_e.html

and get
http://www.os.rim.or.jp/~gigo/over115K/SHSNT4U1.ZIP

Alpha NT version of SHSMOD

Hi

Is there a version of SHSMOD to run on Windows NT on Alpha CPUs ? I would be very interested in one - my Alpha PC has an SMC FDC37C669 I/O chip.

I have access to all Alpha compilers if you would like help in compiling this product to run on Alpha NT.

Regards
Pete

So what do I do with this?

Please forgive my lack of expertise....wanted to make sure I made the next move I make the correct one

question

I have the following message displayed.......
shsmod v1.7a SMC37B80x at 0370h detected original driver Port 1 (02f8h) Serial Speed Mode Low Port 2 disabled

Twinhead Slimnote 233EX

shsmod V1.8beta1 (29-Apr-1999)
NS PC87338 at 0398h detected
NS Patch driver detected
COM0(03f8h):Supported, Mode = High
COM1(03e8h):Unsupported.
Warning -- This system has unsupported UART chip.
The patch may cause problem.
comment:
The 1.8 beta now recognised the port adresses for both COM ports, but it still
does not seem to work. It looks as if the baud rate divisor is set OK, but the
prescaler is still on 13 instead of 1.625. I have to set it to 921600 to get 115k2.
I tried version 1.7a but it could not recognise the port adresses. Also when I use
Inports to read the uart registers it looked as if the baud rate divisor was set in
bank 1 and bank 2. The lock and extended mode bits in EXCR1 and 2 were not set.
By the way I am running W95 US edition.

w83877ATF super io chip

windows98
comment:
isdn ta (degetel 700u)

SHSMOD V1.8 beta 1 release

it works great on my abit bh6. i followed the 1.7a manual to edit the registry and the shsmod correctly set the baud rate to 921600 although it gave the unsupported uart... message during bootup. will test further with online gaming at igz.

keep up the good work!

mike v.

SHSMOD V1.8 beta 1 release

it works great on my abit bh6. i followed the 1.7a manual to edit the registry and the shsmod correctly set the baud rate to 921600 although it gave the unsupported uart... message during bootup. will test further with online gaming at igz.

keep up the good work!

mike v.

problems

I have a gateway and with my modem being recognized on COM2, I'm running windows 98, when I run the program it upgraded com1 but under com2 says default. What does this mean? Can I upgrade my modem port? I need help

1st motherboard VA503+ amd k6/2 at 300mhz

ok, first off, I have an ( LT 56k Win modem )
for this modem to work on com2 win win95
the comm port must be disabled in the bios
before the machine starts, or windows won't
configure the modem and port properly
SO in order for this program to work in win95
when the port is active the program must be
started of ran after win95 starts and sets up
the ports, now, the program did do what it was
made to do, good job, My mouse is on com 1
when i ran the program from my autoexec.bat
default settings, the mouse locked up, the mouse
driver it self can not handly the speed, Now if
you can get the program to run after win95, and
set the speed to high, then i like to test it
and see how it turns out, most win modems are
ran from software type programing, that might
speed up the modem it self, ok, let me what you
all think, tardjr@hotmail.com
comment:

SHSMOD V1.8 beta 1 release

1)Support ALI M1543C.
It is mistaken for 1543 by older version. The mistake makes somewhat strange
behavior.

2)It warns when it can't be applied.

ex.
shsmod V1.8beta1 (29-Apr-1999)
***Force 87308***
NS PC87308 at 002eh detected
Original driver detected
COM0(03f8h):Supported, Mode = High.
COM1(02f8h):Supported, Mode = Low.
COM2(02e8h):Unsupported.
Warning -- PS/2 Mouse not equipped.
You must set low for serial mouse port.
Warning -- This system has unsupported UART chip.
The patch may cause problem.

Of course it can't always warn in all the wrong cases.
Unnecessary warning will be sometimes taken out.

Please report it.

shs18b01.zip 27,030bytes
shs17.zip is necessary for the manual, too.

FIC 2013

shsmod V1.7a (29-Aug-1998)
Winbond W83977 at 03f0h detected
Winbond Patch driver detected
Port1(03f8h) Serial Speed Mode: High
Port2(02f8h) Serial Speed Mode: disabled
comment:
When I load the patch everything appears ok.

When I restart my win98 and invoke my modem, it can not be found. When I
uninstall shsmod it works fine.

I have uninstalled my modem after patching and reinstalling and that also
didn't help.

Any assistance would be greatly appreciated. Thank you.

ASUS P2L97 P-300

shsmod V1.7a (29-Aug-1998)
Winbond W83977 at 03f0h detected
Winbond Patch driver detected
Port1(03f8h) Serial Speed Mode: High
Port2(02f8h) Serial Speed Mode: High

Is tested the serial port speed up to 230k with a Sanyo digital camera :
It works fine...
But my US Robotics Sporster Voice 33.6 coonected to the other port is not able to answer at higher speed than 115k ! Too bad !

FIC VL-601, Pentium II 233 mhz 64 Mb ram

shsmod V1.7a (29-Aug-1998)
Winbond W83977 at 03f0h detected
Winbond Patch driver detected
Port1(03f8h) Serial Speed Mode: Low
Port2(02f8h) Serial Speed Mode: High

comment:
Actually, the Winbond I/O chip is a 89377TF-A . My dual mode Cyberconnect modem
is connected to port 2, which is set at 230400 bps. That gives me a download
speed of 5 Kilobytes /s, even though i can never connect at higher rates than
48000 kilobits/s and sometimes as low as 46000. So, this utility is brilliant!

Abit BX6 rev. 2.0

shsmod V1.7c (17-Feb-1999)
Winbond W83977EF at 03f0h detected
Winbond Patch driver detected
Port1(03f8h) Serial Speed Mode: Low
Port2(02f8h) Serial Speed Mode: High

comment:
I have an external Zoom 56K modem on com2. When I install shsmod, I see max speed 38400 or 19200 when i check "more info" in control panel --> modems. I then can not reinstall my modem properly with shsmod installed. Is this an incompatibility with this winbond chip? I am connected to the internet right now using the 230400 DTE speed and 45333 modem speed, so it seems to work with dialup networking. Is there a good program for testing the serial port and modem communication at speeds over 115K?

deleted as user request

Asus P2B

shsmod V1.7c (17-Feb-1999)
Winbond W83977 at 03f0h detected
Winbond Patch driver detected
Port1(03f8h) Serial Speed Mode: High
Port2(02f8h) Serial Speed Mode: High

comment:
When i get "More info" using the modems applet in the control panel i notice that my max speed is reported as 38.4k Baud. I have the port set to 921600 at my modem is set at 230400. i edited the registry to make the maxim speed 921600. What is going on?

Abit LX6



Not SMC37C665IR/666IR/669/669FR/93x/93xFR/93xAPM/957FR chip !!!


comment:
I run WinNT - Danish
The serial.sys file is
45.424 bytes large.

I can't seem to findout witch comport I have. Smsmod works fine when I use Win98.

How do I figure out the name of the chip ?
It their not a newer version og the "SHSNT4U1.ZIP 44K update 22-Feb-97" ??

Please email me at: r@sser.dk

HP Pavilion 8160

C:\>C:\SERIAL~1\SHSMOD.EXE B H
shsmod V1.7a (29-Aug-1998)
NS PC87307 at 015ch detected
NS Patch driver detected
Port1(03f8h) Serial Speed Mode: High
Port2(02f8h) Serial Speed Mode: High

comment:
It would appear that we have success, however, I do not see any changes in speed. I am using an LT 56K modem.

Modem is configured for 115200, please advise of any additional steps required.

Thanks!

shsmod1.7c

Support W83977EF chip.

shs17c.zip 23,322bytes

IBM Aptiva E3N w/ AMD-K6-2 processor @ 300 Mhz

shsmod V1.7a (29-Aug-1998)
ALI M1543 at 03f0h detected
Original driver detected
Port1(03f8h) Serial Speed Mode: Low
Port2(02f8h) Serial Speed Mode: Low

comment:

Lucent Lt win Modem

What do I do from here?

Packard Bell/ Cyrix MII-300/ Lucent LT Win Modem

shsmod V1.7a (29-Aug-1998)
Winbond W83877TF at 03f0h detected
Winbond Patch driver detected
Port1(02f8h) Serial Speed Mode: High
Port2 disabled

comment:
Everything seemed to go well except that I cannot select a speed past 115k. I read the read me file and those hints didn't work. I am running Windows 98. Please help.

ASUS P/I-P55T2P4

SHSNT4U1.COM only supports SMC chipset
comment:
Do you have a WinNT4.0 version (SHSNT4U1.ZIP) for ASUS board with Winbond 83877F yet? Thank you! --greg

Tyan S1590S motherboard

shsmod V1.7b
winbound W83877TF at 03f0h detected
driver detected
Port1(03f8h) Serial Speed Mode: High
Port2(02f8h) Serial Speed Mode: High
comment:
Tyan S1590S motherboard worked great with SHS17.zip Running Windows98
Problem: My modem is on COM4 and under +COM PORTS&LPT I only see COM1&2 and my
LPT port listed.
Under Modem properties I see my modem is on COM4. I know this to be true.
How can I change the Setting if I can not get to the proerties of Com4?

SOYO 5EHM

shsmod V1.7a (29-Aug-1998)
SMC37C669 at 03f0h detected
SMC/ALI Patch driver detected
Port1(03f8h) Serial Speed Mode: High
Port2(02f8h) Serial Speed Mode: High

comment:
Working great in Win 98. Thank you for a great program!

Abit BH6

shsmod v1.7a (29-Aug-1998)
Winbond W83977 at 03f0h detected
winbond Patch driver detected
port1(03f8h) Serial Speed Mode: High
port2(02f8h) Serial speed mode: High
comment:
It only seems to work up to 230k, but it may regard to a problem with my TA
(Zyxel Omninet+) But at 230k it work´s just perfect.

Internal modem

Hello Rulph.

The SHS V1.7 isn't able to support serial port that provided by WinBond or NS
chip and serial port that provided by ordinary chip simultaneously.

It is mainly code space problem, because SHS is only patch.

I'd like to know how to assign driver for supported chip only.

shsmod V1.7

Dell Dimension XPS Pro200n

shsmod V1.7a (29-Aug-1998)
NS PC87307 at 002eh detected
NS Patch driver detected
Port1(03f8h) Serial Speed Mode: High
Port2(03e8h) Serial Speed Mode: High

The program worked with the promised results, but my system was unable to
initialize the US Robotics 56K V.90 Internal modem on COM 2, Interrupt
Request 03, 02F8-02FF . I had to uninstall shsmod. Can anyone explain why,
or point to a location where I can find additional information. Thanks.

shsmod V1.7

Dell Dimension XPS Pro200n

shsmod V1.7a (29-Aug-1998)
NS PC87307 at 002eh detected
NS Patch driver detected
Port1(03f8h) Serial Speed Mode: High
Port2(03e8h) Serial Speed Mode: High

The program worked with the promised results, but my system was unable to
initialize the US Robotics 56K V.90 Internal modem on COM 2, Interrupt
Request 03, 02F8-02FF . I had to uninstall shsmod. Can anyone explain why,
or point to a location where I can find additional information. Thanks.

Tyan S1562S

I ran your program and patch with the Tyan S1562S and it went well. For your information, it detected an SMC 37c665ir chip. Thanks.

Compaq Deskpro EN 9400

shsmod V1.7a (29-Aug-1998)
NS PC97307 at 015ch detected
Port1(03f8h) Serial Speed Mode: Low
Port2(02f8h) Serial Speed Mode: High

comment:
Why does SHSMOD say "High" for my Port2 when I have not installed the
patch yet? (I booted with a floppy in DOS to run SHSMOD)

I am using NT4 with service pack 4. My serial driver (SERIAL.SYS) is
45360 bytes long. Do you have a patch for the 45360byte NT driver file?

I am trying to use a 3com ImpactIQ modem at 230K. I am thankful for any
help you can give me.

-Mike

Compaq Deskpro EN 9400

shsmod V1.7a (29-Aug-1998)
NS PC97307 at 015ch detected
Port1(03f8h) Serial Speed Mode: Low
Port2(02f8h) Serial Speed Mode: High

comment:
Why does SHSMOD say "High" for my Port2 when I have not installed the
patch yet? (I booted with a floppy in DOS to run SHSMOD)

I am using NT4 with service pack 4. My serial driver (SERIAL.SYS) is
45360 bytes long. Do you have a patch for the 45360byte NT driver file?

I am trying to use a 3com ImpactIQ modem at 230K. I am thankful for any
help you can give me.

-Mike

Compaq Deskpro EN 9400

shsmod V1.7a (29-Aug-1998)
NS PC97307 at 015ch detected
Port1(03f8h) Serial Speed Mode: Low
Port2(02f8h) Serial Speed Mode: High

comment:
Why does SHSMOD say "High" for my Port2 when I have not installed the
patch yet? (I booted with a floppy in DOS to run SHSMOD)

I am using NT4 with service pack 4. My serial driver (SERIAL.SYS) is
45360 bytes long. Do you have a patch for the 45360byte NT driver file?

I am trying to use a 3com ImpactIQ modem at 230K. I am thankful for any
help you can give me.

-Mike

P2-300 Abit Bh6

Winbond W83977 at 03f0h detected
Original driver detected
Port 1 (03f8h) serial Speed Mode (low)
Port 2 disabled
comment:
I seem to have a problem, I installed the program as directed and the speed
increase resulted, but it would not recognize Com 2 which my modem resides on.
Also after installing, my mouse on Com 1 could not be recognized. My question
is.. How do I get it to recognize Com2 and increase the rate, while not
increasing the rate of Com1 so I can retain use of my mouse. Thanks

re;Read Back BootPartition of Bootable Cd

Because BootImage is a file in Bootable CD that was made by mkbootcd.
It has no problem.
Do you want the bootimage takes out from product CD ?
If so, you must pay attention to the copyright.

First of all you take out the ISO image from CD with winimage.
The ISO image is verifyed with mkbootcd to display the position and size of bootimage.
Take out the part with the binary editor like hexedit.

Read Back BootPartition of Bootable Cd

Does anyone know if it's possible to read the partition part of a bootable CD back to a image file. If so how???

grtx,
Eddy

ASUS P2B Rev 1.02 230400 bps

Thanks for this great software. I can now speak to my external modem at a
DTE speed of 230400. I have now eliminated the serial line bottleneck and can
make full use of my V.90 modem!

Well Done!

Serial driver version 4.13 with HighSpeedMode V1.7a(Linux 06-Sep-98) enabled
tty00 at 0x03f8 (irq = 4) is a 16550A(Winbond W83977 at 03f0h, Serial Speed Mode: High)
tty01 at 0x02f8 (irq = 3) is a 16550A(Winbond W83977 at 03f0h, Serial Speed Mode: High)
(The chip is marked Winbond W83977TF-AW).

FAQ 7)

Q. Does this program help throughput of data with v90 modems or is 115200 already fast enough?

A. If your modem reaches maximum compression ratio at max speed, 115200 is too slow.
But it depends your modem,line,machine,provider conditions.

FAQ 6)

Q. After running the program, I get confirmation that the ports are set to high. However my control
panel - modem - properties - maximum speed is still 115200 and cannot be set any higher. Does this
mean that the modem will not communicate above this speed despite the setting being higher under the
comm port setting?

A. Once again, The properties no exact relation of actual speed.
If your modem's modem.inf not support over115K, you must edit it.

FAQ 5)

Q.Looking in control panel - system - comm port properties I already have
option for 230400/460800/921600 bps. Do I need to use your program?
A.The properties no relation of actual speed.
If you want know actual speed, connect your modem with hyperterminal
and check DTE speed. Almost modem respond it by "AT\S" command.
caution:
The hyperterminal's baudrate not change at when properties was changed.
It is change made at connect.If the DTE speed not same as properties,
disconnect and connect again.

FAQ 4)

Q. My serial mouse can't work.
A. Please read trouble shooting section in document.
(Winbond only)

FAQ 3)

Q. My NS87338 chip can't work collectly.
A. The SHSMOD can't support some NS87338 completely. I doubt
NS97338 chip has same chip ID and revision.

FAQ 2)

Q. The SHSMOD said "2nd port is disabled."
A.
1)In windows98, Disabled by ACPI. don't mind.
2)Your chip is ALI M1543C. The SHSMOD not support M1543C.
Unfortunately I don't know how to identify 'C' version yet.
3)The port that provided by MIO chip is disabled. The 2nd
port provided by other source.(Internal Modem, DSP, etc.)

FAQ 1)

Q. The internal modem/TA can't work with SHSMOD.
A. If you have internal modem only and WinBond or NS chip on motherboard,
uninstall SHSMOD.
The SHSMOD has no merit with internal modem/TA.

re;maxtrans

>0018 00 C2 01 00

MaxTrans

I would like to maximize my transmisson rate and according to your instructions I should edit bytes 24 (0x18th) - 27. by editing the registry. My question.. which is the 24th byte in the following example? After clicking properties on Hotkey-local-machine I get the following...

VALUE DATA
0000 80 01 00 00 FF 00 00 00
0008 FF 00 00 00 07 00 00 00
0010 0F 00 00 00 FF 07 00 00
0018 00 C2 01 00 C0 DA 00 00
0020

Pentium MMX 200Mhz ( Intel)/ TXPro motherboard

ALI MI543 at 03f0h detected
SMC/ALI Patch driver detected
Port 1 (03F8h) serial speed mode : high
Port 2 (02F8h) serial speed mode : high

comment:
My modem is a Zoom Dualmodem V90 and 56k. My problem is that it is
installed at Comm 4, address 02E8h and due to a mistake I made in its
instalation I can't change that. How can I make shmod recognize and accelerate
this Comm at this address ?
Thank you

Microstar MS-6111

Winbond W83977 at 03f0h detected
Original driver detected
Poart1(03f8h)Serial Speed Mode:Low
Poart2(02f8h)Serial Speed Mode:Low

IBM Aptiva

shmod V1.7a
smg37c93x at 0370h detected
snc / ali patch driver detected
Port1 (02e8h) Serial Port mode : High
Port2 disabled

comment:
My question is this: port1 (02E8h) corresponds to com4. My modem is connected to (03F8h) com1. How can I get shsmod to configure (03F8h) com1. I cannot change the modem to use com4 even though I changed the jumpers to com4, Win95 still automatically uses com1. Thanks in advance.

cgi test

test cgi

MS5169

shsmod V1.7b
XXXXXXXXXXX at 0XXXh detected
XXXXXXXXX driver detected
Port1(0XXXh) Serial Speed Mode: High
Port2(0XXXh) Serial Speed Mode: High
comment:
Test new post form.

Abit BH6 running Win98, Matrox G200, Symbios SCSI, Vortex Sound

Sorry don't have it installed anymore but it
reported some kind of windbond chip installed
and said both ports supported high speed mode.
After installing the software I could set the
port speeds to 916K in the Win98 properties.
comment:
What happened for me was that my ports stopped working altogether after
installing this program. My 3Com Impact IQ could no longer talk to the port,
even when turned back down to 115K. Worse, something was polling my system
every 3 seconds or so. This would lock up my video and cause my sound to skip.
This happened all the time, but was particularly insidious when trying to play
games. They would pause at this regular 3 second intervals. Remming out the
line in the autoexec did not fix the problem. Uninstalling the software did fix the
problem.

My system is as follows:
Abit BH6 motherboard (bx chipset)
Celeron 300a
AGP slot: Matrox G200
PCI slot1: Symbios UW SCSI
PCI slot2: Diamond Monster Voodoo 1
PCI slot3: Magicwave Vortex based soundcard
PCI slot4: Netgear fast ethernet card
ISA slot5: Sportster 128 ISDN
ISA slot6: PPI 28.8 modem (com4)
com1 and com2 are both active

Registry edit

In addition to my two previous post, I would like to add the following:
I thought it may help. Aftre installing the shsmod I get the following

shsmod v1.7a (29-Aug-98)
smc37c93x at 0370h detected
smc / ali patch driver detected
port1 (02e8h)serial port mode: high
port2 disabled

As per the device manager\properties, my 56k modem is using I/O resources 03f8-03ff
IRQ 4.. hope this helps...

regedit

BTW the e mail is bandito@interactive.net The o in bandito is the letter o not the
number 0. Thanks.

Registry edit

I downloaded and installed the shdmod exec for win 95 and I got the following.
Port 1 is high and port two is disabled. My 56k modem is connecting only at
31200. I attempted to edit the registry using the appended suggestions in
the installation doc and as suggested I looked for the Com(x)..or in my case
com1 where my 56k modem is attached (as per the modems icon in the control
panel). My problem: (1)After looking in regedit the .../class/modem/nnnn
(i looked at both 0000 and 0002) i did not find the attachto to edit the
bps and value as was suggested in the doc.. (2)My next question is what does
the nnnn refer to? I am assuming it refers to the com port number ... If
that is the case then 0000 is com port(1) and 0002 is comp port(2)..Is this
correct? If so, the data in regedit referring to my 56k modem is in 0002 or
com port(2). Could this be the reason i am connecting at 31200? I noticed
the modem response values in 0001 (where my 56k modem is goes up to 33600
only whereas in 0002 my modem response values go to 56000.
In summary:
As per control panel\modems - com1 is where the 56k modem is.
As per regedit ... class\modem (nnnn) 0000 modem values go to 33600.
As per regedit ... class\modem (nnnn) 0002 modem values go to 56000.
As per shsmod.exe port1 = high, port2 disabled.
Question: Where is my 56k modem really attached to (as per regedit 0000 or
0002)? If 0002, how do I enable 0002? If 0000, how to i get my
regit edit to recognize the 56k modem? Thanks in advance for your
help.

Connecting at 14400 after installing SHSMOD v1.7

I installed SHSMOD 1.7 on my IBM Thinkpad 385ED. Prior to installation,
I would connect at 115200 and get download speeds of 5-6kbs per second.
After installation, the Impact IQ would only connect at 14400. I read
the instructions about modifying the settings with regedit, but I don't
understand them. The only data on that line is "com1". How do you modify
digits required, or is this even the problem? I uninstalled and am very
anxious to get it working right. This could be the greatest thing since
sliced bread!!

SHSMOD problem with modem

HI, further to my post below, Do I need a driver for my modem to support the
higher speed or do I need a new modem altogether (ISDN) or something similar
in order to use the higher speeds? Pardon my ignorance as I am just an ordinary
user and has limited knowledge.

SHSMOD problem with modem

HI, I installed SHSMOD 1.7 and the installation went without a problem. The
ports were detected and set to high speed at Dos. But my modem just doesn't
respond to the higher speeds. My chips are SMC37C669 and I changed the registry
to 460,800 as suggested in SHSMOD instructions and also set the modem to that
speed together with the serial ports speed in device manager but win95 gives a
'No response from modem' message. My modem is a Well X2 (USR 56K X2 compatible).
I have no problems if I set it back to 115200. Can someone advice?

SHS17

I am using an "internal modem". Both Serial Ports have been disabled to provide additional
IRQ's. The program detected both serial ports, even though they were disabled. The
Device Manager shows only LPT1 even though my internal modem is using COM1.

Could someone please help me understand, if I will benefit from SHS17. I'm using a
56K Flex (Lucent Chipset) By Viking Components. It was not detected, only the
serial ports 1 & 2.

Thanks!
Jim

230k on gateway solo 9100xl notebook

the shsmod detect utility said I had a NS PC87338 serial UART and installed
the high speed drivers. When I set the port to 230K, it still seams to only
run at a maximum of 115k with a 3com IQ ISDN modem connected. Anybody have
any ideas?

SHSMOD V1.7

Hi,

I Use Gigabyte 586SG, the program is installed fine, but my mouse is down on COM1; though I try to decrease to 4800 still doesn't work. Any idea what's going on?

My mouse is Logitech "MouseMan". Use Windows98 driver.

TKS

FC

RE:multi-boot cd-rom

I don't do that. The reason is I think I'm not only person who can do it.
There are the persons who are reporting that it already succeeded.
And I don't have Easy CD-Creator3.5.

My present priority in hobby time is as follows :

1. IR-remote function implementation for Garmin'Me.
Garmin'Me is conversion hardware for NMEA GPS format to SONY IPS GPS format.
That was made by me. The related pages are Japanese only.

2. Drive.
Fall of Japan is a very good season.
And I had bought a new car, HONDA integra 98Spec.R :-)

3. The SHSMODE utility version 1.7a for NT.
As for this, there are dozens of requests already.

Anyone other than my friends, son and daughter can not change this priority.

And, I am working hard till late night because I am Japanese. :-):-)

Accordingly there is only one method.
The method is that you become my friend.
It is not difficult.
Do contribution. that is way to my friend.

multi-boot cd-rom

Mr Gigo,
can you get us a step by step guide to creating a multi-boot menu CD pls? I am sure this will benefit many many people..

tks

Tyan S1563S Motherboard

Tyan S1563S motherboard worked great with SHS17.zip Running Windows98

Problem: My modem is on COM3 and under +COM PORTS&LPT I only see COM1&2 and my
LPT port listed.

Under Modem properties I see my modem is on COM3. I know this to be true.

How can I change the Setting if I can not get to the proerties of Com3?

Thanks

Write to Bulletin Board

[Return to home]